Heating Repair in Edmonton, AB
Heating breakdowns in Edmonton during winter are emergencies—temperatures can drop to dangerous levels within hours. HVAC specialists quickly diagnose issues with furnaces, boilers, and heat pumps, then repair or replace faulty components.
Typical heating repair costs in Edmonton: CA$200–CA$1,200
- Serving Edmonton & Edmonton Metropolitan Region
- Licensed by Alberta Municipal Affairs (no provincial licence; WCB required)
- Free Estimates
- Response in <2 Hours
Heating Repair in Edmonton, AB
Heating breakdowns in Edmonton during winter are emergencies—temperatures can drop to dangerous levels within hours. HVAC specialists quickly diagnose issues with furnaces, boilers, and heat pumps, then repair or replace faulty components. Many contractors in the Edmonton area offer 24/7 emergency service so you're not left without heat during the coldest months.
Alberta's freeze-thaw cycles and extreme cold stress heating systems heavily. Local HVAC pros in neighborhoods like Millwoods and West Edmonton often see increased demand for repairs in November and December, so booking early prevents long wait times when you need warmth most.
All contractors in the Edmonton network are licensed through Alberta Municipal Affairs (no provincial licence; WCB required) and carry full general liability and workers' compensation insurance. Permits are pulled through City of Edmonton Sustainable Development. Edmonton experiences heavy snow, extreme cold, freeze-thaw cycles, ice dams, hail and chinook winds — hiring a locally-experienced contractor is essential.
Signs You Need Heating Repair in Edmonton, AB
Any of these indicators warrants a call to a licensed Edmonton HVAC contractor. Addressing HVAC issues early prevents costly repairs and system failure.
- Furnace ignites but burner shuts off immediately (flame sensor/pressure switch fault)
- CO detector alarm or smell of burning from the vents
- Uneven heating — some rooms cold while others are warm
- Short cycling: system turns on and off more than 4-6 times per hour
- Yellow or orange burner flame instead of blue (incomplete combustion risk)
- Heating bill increased 25% or more without a change in weather or usage
What Heating Repair Includes
Here’s what a licensed Edmonton HVAC contractor covers during a typical heating repair call:
- Heat exchanger integrity test
- Ignitor and gas valve inspection
- Pressure switch and inducer motor test
- Flue and venting inspection
- Carbon monoxide safety test
- Full heating cycle performance test
Scope may vary by contractor. Ask your contractor to confirm what’s included before work begins.
How Heating Repair Works in Edmonton
What to expect from a licensed Edmonton HVAC contractor from first call to completion.
- 1
Safety Check First (CO test, gas leak sniff)
Before diagnosing performance issues, the technician tests for CO presence and checks gas connections for leaks. Safety issues are addressed before any other repair work begins.
- 2
Diagnostic Scan
Control board fault codes are read, and key components — ignitor, flame sensor, pressure switches, inducer motor, and heat exchanger — are inspected and tested.
- 3
Repair & Parts Replacement
Failed components are replaced with OEM or compatible parts. Gas valve, ignitor, and circuit board replacements are common; all are tested after installation.
- 4
Combustion Test
After repairs, combustion efficiency is verified: burner flame color, CO output, and flue gas temperature confirm safe and efficient operation.
- 5
Full Heating Cycle Test
System is run through a complete heating cycle. Temperature rise across the heat exchanger is measured to confirm the unit is operating within manufacturer specs.
Frequently Asked Questions About Heating Repair in Edmonton, AB
What should I check before calling an HVAC technician for a heating problem?
Before calling a pro, verify your thermostat is set to Heat mode (not Cool) and the temperature is above room temperature; check that your air filter isn't completely clogged (restricts airflow and can trigger safety shutoff); confirm the furnace switch and breaker are on; and check that your gas supply valve is open. If the pilot light is out on an older unit, follow the relighting instructions on the furnace door. If you smell gas, leave the home immediately and call your gas utility.
Why is my heat pump blowing cold air in heating mode?
Heat pumps blow air that feels cooler than gas furnace output — typically 90–100°F versus 130°F from a gas furnace. If the air is room temperature or below, the unit may be stuck in defrost mode (normal, lasts 5–15 minutes), have a refrigerant leak, a faulty reversing valve, or a bad defrost control board. A licensed technician can diagnose the issue within one visit.
How long does a furnace last?
Gas furnaces typically last 15–20 years with regular maintenance. Heat pumps last 12–15 years. Electric furnaces can last 20–30 years. Regular annual maintenance (filter changes, burner cleaning, heat exchanger inspection) keeps systems at the high end of these ranges. If your furnace is over 15 years old and needs a major repair, replacement is often the better investment.
Other Hvac Services in Edmonton, AB
For Hvac Professionals
Are you a hvac contractor serving Edmonton?
ProvenQuote leases city markets exclusively to one contractor — every lead from this page, no sharing. Free to apply, no commitment.